D-Link Router Setup: Ultimate Guide At Your Fingertips

D-Link is one of the most preferred routers throughout the globe. It left behind its competitors by providing exceptional features and superior connectivity. A D-Link wireless router can help you to build a protected home network for all of your wireless and wired devices. Moreover, it also allows you to connect the internet connection with several devices. But Before using the D-Link router, you need to configure the wireless settings and the internet at first. So, if you have just purchased a D-Link router and want to avail the fast Wi-Fi connection, then this article can help you by providing a D-Link router setup guide. Hence, you are advised to go through the guide given below. So, let’s start.

D-Link Router Setup: Try Out the Easy Hacks

Let’s have a look at the Step-by-Step setup guide explained below to successfully setup your D-Link router:

Step 1: Connect the Hardware:

After unboxing the router, first, you have to assemble the hardware. Here are the steps to do that:

Turn off or Disconnect the Modem:

Before going to connect the router with the modem, you need to power off the modem. If you are unable to power off the modem, then you should remove the plug of the modem from the power outlet.

Connect the Ethernet Cables:

Here you need two Ethernet cables to set up the D-Link router. One cable is to connect the router with the modem, and the other is to attach the router with the computer. After completing the setup procedure, you should connect the computer wirelessly if you have a broadcast network adapter. The modem or router always comes included with one Ethernet cable. If the system was connected straight to the modem previously, then you can use that Ethernet cable.

Connect the Modem with the WAN:

Now, you have to connect the Ethernet port on the back side of your router. The Ethernet port has a distinct color than the other four LAN ports. Here, keep the power supply of the router disconnected.

Connect the LAN Port with the Ethernet Port:

Usually, you can find the Ethernet port of the system on its backside. Therefore, connect the LAN port with this Ethernet port.

Turn on the Modem:

Now, plug in the modem with the power supply and turn it on. After that, you have to wait for a few seconds until the modem boots up.  

Turn on the Router:

Next, connect the router with the power supply and turn it on. It will also take a few seconds to boot up.

Turn on the Computer:

If the system is not powered on, then turn it on. Then, you have to confirm that you are not connected with another broadcast network.  

Check the Power Light of the Router:

After that, you have to check the power indicator of your router. You should check the WAN light, Power light, as well as the LAN light of the LAN port of the system. If you see that the WAN light is off, then you need to confirm that the modem is turned on as well as it is connected with the WAN port of the router. If you see that the LAN light is off, then you should check that the computer is connected through the Ethernet cable to the LAN port of the router. You also need to make sure that the router is turned on.

Step 2: Access the Router

After assembling the hardware, you have to access the D-Link router. To access the router, you should perform the steps as follows:

Configure the Router:

At first, you have to open the default web browser of the system. Now, move the cursor to the address bar and type ‘.192.168.0.1’. Now, hit the Enter key from the keyboard to load the address bar. Now, the window prompts to enter the login credential while loading the address bar. Here you have to enter the default IP address of your D-Link broadcast router.

If it still does not load the configuration page of the router, then you should check whether the system is connected with the router and not with other networks. Else, you can also press the Reset button and hold it for a minimum of ten seconds. It will then reset the D-Link router to the default configuration settings. After that, you can easily access the configuration page of the router.  

Enter the Login Detail:

Next, you have to type ‘admin’ on the User Name box. Here, you should leave the Password box empty. It is the default login credential for the D-Link router.

But, if this login detail does not work, then it indicates that someone has modified the login information. Hence, again you have to reset the D-Link router by pressing the Reset button from the back side of the router. After resetting, you will be able to login using the default login detail.  

Step 3: Perform the First-time Setup

Now, perform the setup procedures stated below:

Run the Router:

After entering the login credential, you should tap on the ‘log in’ button. Then, you should navigate to the ‘Setup Wizard’ section. It will get the network configured as well as secured in just a few seconds. But, if you see that the ‘Setup Wizard’ category is missing, then you should find it by going to the ‘Setup’ tab.

After setting up the D-Link router, if you are logging in to modify the settings, then you have to go to the ‘Adjusting Settings’ category.  

Setup the Internet Connection:

Tap on the ‘Launch Internet Connection Setup Wizard’ option. As a result, it will initiate the setup procedure for the administrator account and the internet connection of the router. Then, tap on the ‘Next’ button to proceed further.  

Create the Administrator Password:

Next, you are prompted to create a password for your administrator account. Move the cursor to the ‘Password’ field and enter your desired password. Then, enter the same password in the ‘Verify Password’ box. Tap on the ‘Next’ button.

Set the Timezone:

Now, you have to set the current timezone for the specific logs as well as for the time-based settings of the D-Link router. Hence, tap on the drop-down menu and choose the proper timezone.

Select the Internet Connection type:

Most of the home users who are connected through the DSL or cable will choose the first option, i.e, ‘DHCP Connection.’ If you are not sure about this, then you should verify it by connecting with your internet service provider.  

Fill the MAC Address Box:

Tap on the ‘Clone Your PC MAC Address’ option. Click this only when the ‘MAC Address’ box is empty. Most of the users can neglect the hostname field except it is specified by the internet service provider.

Save the Settings:

Tap on the ‘Connect’ button to apply the changes settings. Now, the router will start to reboot by itself. This will take a few seconds. Wait until the reboot process completes.

Test the Connection:

Launch your default web browser to check if you can load the web page. Once you have seen that the web page is loading properly, then you should move on to the next part.

Step 4: Create a Broadcast Network

Next, you have to create a broadcast network. Hence, you should have a look at the steps given below:

Login to the Router:

At first, open the web browser and then type ‘192.168.0.1’ by going to the address bar. After that, you have to log into the router by entering the username and password that you have set previously. Then, tap on the ‘Log in’ option.

Open Setup Wizard Window:

Now, you have to navigate to the upper left side of the window and tap on the ‘Setup’ tab. It will head you over to the ‘Setup Wizards’ window.

Enable the Wi-Fi Connection:

Go to the ‘Wireless Settings’ menu by going to the left pane of the window. It will navigate you to the new page that allows you to set up the broadcast network. Now, you have to tick the ‘Enable Wireless’ box. It will turn the broadcast network on after saving the settings.

Set the Network Name:

Next, you have to provide the network name. This name will be visible publicly. Hence, you have to make sure that you don’t include your personal info. Now, you have to choose the ‘Security Mode’ and tap on the ‘WPA2’ option. It is the most secure way to transmit the broadcast network. If you are using an older device, then you should choose the ‘WEP’ or ‘WPA’ option.  

Create Password:

After that, you have to make a strong password. Choose the ‘Cipher Type’ option. Then, select either the ‘Personal’ or ‘Enterprise’ option. Tap on the ‘Passphrase’ option and give your desired password. Enter the same password in the ‘Confirm Passphrase’ box.

Save the Settings:

Tap on the ‘Save Settings’ option. Now, you will see that the broadcast settings will be saved automatically. Here you will also see that the broadcast network is turned on. It may take a few minutes. When the router has saved the recent changes, then you can easily connect the devices with the network wirelessly.

Connect the Device:

Now, you will see that the broadcast network is enabled. Hence, you should connect the devices with the router. The procedure differs depending on the system. But usually, you have to choose the broadcast network name from the list of available Wi-Fi networks. Then, you should type the password that you have created recently. For most of the devices, you have to connect with the broadcast network.

Step 5: Adjust the Settings

After creating the wireless network, you have to adjust the settings of the network. To perform this, you should follow the steps given below:

Change the Wireless Settings:

If you want to change the wireless network settings, then navigate to the upper left side of the window and tap on the Setup tab. Then, go to the ‘Wireless Settings’ section. Tap on the ‘Extended Range Mode’ option.  

Setup Port Forwarding:

Now, if you want to set up the port forwarding application to run any particular program on the system, then you have to tap on the ‘Port Forwarding’ category by going to the ‘Advanced’ tab. Type the IP address of the system while setting up the port forwarding application. After that, you have to provide the range of ports that you wish to open.  

Create Website Filters:  

To block the access of any particular websites, you can also set up the router. Navigate to the upper left side of the router configuration page and tap on the ‘Advanced’ tab. Choose the ‘Website Filter’ option from the list. Then, enter the sites which you wish to block. Then, tap on the ‘enable’ button.  

Activate the Gaming Mode:

If you want to use the router to play games, then you have to enable the Gaming Mode. It can improve the connection as well as allow you to get more matches. Therefore, navigate to the ‘Advanced’ tab. Choose the ‘Advanced Network’ option from the list. Now, check the box that prompts ‘Enable Gaming Mode.’ As a result, it will reroute the gaming traffic to improve its performance. Hence, it’s better to disable this when you are not playing games.

Final Recommendation

In the above guide, we have provided some of the easiest ways to setup the D-Link router. We hope if you implement the above ways in their respective order, then it will definitely assist you to ease up your pain. After successfully performing the above ways, if you still face any kinds of trouble, then it is best to seek help from a tech expert for further assistance. In addition, you can also share your queries ad valuable feedback through the comment box given at the end of this post.